How Much of Each Chemical to Add to Your Pool (2024)

You know you should be adding chemicals to your pool. But exactly how much do you need to add? For example, it only takes about half a pound of pH Decreaser or a gallon of liquid chlorine to balance a 10,000-gallon pool. But the dosing depends on the size of your pool and your current chemistry levels. So here’s a quick guide on how much of each pool chemical you need to add to your water.

Here’s The Right Way to Add Chemicals To Your Pool Water

1. Test your water first. You won’t know how much you need to add unless you know where your levels are at.
2. Add your chemicals in the right order. Make sure you adjust your alkalinity first, then your pH, and finally your chlorine in that order. Each one has a domino effect on the next one, so balancing them in the right order helps each chemical work properly.
3. When adding chemicals, keep the filter on and running. This will help them circulate and disperse everything in the water.
4. Wait at least 20 minutes between adding chemicals and retest your water between doses. Keep in mind that it will take longer to get a reading on slow-dissolving chemicals, like chlorine pucks.
5. Never mix chemicals outside of the pool. It can cause toxic gas or, worse, an explosion.
6. Always wear the right safety gear, like gloves, goggles, long clothing, and close-toed shoes.

How Much of Each Chemical You Need to Add to Your Pool

You’ll need to know how many gallons of water your pool holds before adding anything. These dosages apply to regular pool chemicals, like alkalinity or pH Increasers, and their substitutes, like baking soda and soda ash. If you’re curious about how to substitute your pool chemicals with household products, be sure to check out our other video.

1. Alkalinity Increaser or Baking Soda

This raises your alkalinity, which should be between 80 and 120 PPM. We usually recommend at least 100 PPM, but 80 is fine.

For every 10,000 gallons of water, you’ll need about 1.5 pounds of Alkalinity Increaser or Baking Soda to raise your alkalinity by 10 PPM. So if you have a 20,000-gallon pool, that’s 3 pounds. And it’s only ¾ of a pound (or 12 ounces) for a 5,000-gallon pool.

For example, let’s say you need to raise your alkalinity by 40 PPM. You’ll need about 6 pounds of alkalinity increaser for a 10,000-gallon pool. Keep in mind that after you raise your alkalinity, your pH might naturally rise with it.

2. pH Increaser or Soda Ash

This raises your pH. Your pH should be between 7.4 and 7.6. For every 10,000 gallons of water, it takes about half a pound (or 6 to 8 ounces) of pH Increaser or Soda Ash to raise your pH by 0.2.

If you have a 20,000-gallon pool, that’s about a pound or 16 ounces of pH increaser. If you have a 5,000-gallon pool, that’s just 4 ounces. If your pH is really low, say lower than 7, start by adding 1 pound of pH increaser at a time for every 10,000 gallons of water and then retesting your levels.

Keep in mind that your total alkalinity will go up slightly, too. But you’ll notice a greater change in pH.

3. pH Decreaser or Muriatic Acid

This lowers both your pH and alkalinity. If your pH is a little high, say between 7.8 and 8.0, you’ll need about 12 ounces or ¾ of a pound of pH Decreaser to bring your pH into range. That’s for 10,000 gallons of water.

That means you need 1.5 pounds for a 20,000-gallon pool and 6 ounces or ¾ of a cup for a 5,000-gallon pool. If you want to use Muriatic Acid instead, check out our other video since there are a lot more safety precautions needed.

Also, it’s pretty common to have trouble balancing your alkalinity and pH. So be sure to check out our other videos, especially on low and high pH, if you need help getting these levels right.

4. Chlorine

Your free chlorine should be between 1 and 3 PPM, with 3 PPM being ideal. Here’s a dosing chart for how much chlorine to add each week. This assumes your chlorine levels aren’t completely out of range and that you just need to add a maintenance dose.

• For chlorine granules, you’ll need 3 to 4 ounces or about half a cup for every 10,000 gallons of water.
• For 3-inch chlorine tablets, add 2 tablets for every 10,000 gallons of pool water. If your pool holds 10,000 gallons of water or more, 3-inch tablets work great. But they can quickly overwhelm smaller pools, so opt for 1-inch tablets, granules, or liquid chlorine instead.
• Add a gallon of liquid chlorine for every 10,000 gallons of water. This is for pool-grade liquid chlorine, not household bleach, which is less strong.

5. Cyanuric Acid

This is also known as Chlorine Stabilizer or CYA. You do not need to add this if you’re using trichlor chlorine tablets or dichlor chlorine granules, as these already contain CYA. If you’re using bleach or liquid chlorine, you’ll need to add this to your water to help protect your chlorine from breaking down in the sun.

Your levels should be between 30 and 50 PPM. If there is no CYA in the water, you’ll need about 3 pounds of stabilizer to bring your levels up to 30 PPM in a 10,000-gallon pool.

Add this slowly and in small batches to your water. If you add too much, the only way to lower your CYA levels is to partially drain and refill your pool with fresh water.

6. Calcium Hardness Increaser

This helps protect your pool’s surfaces and equipment in the long run. The calcium hardness level for vinyl liners or fiberglass pools should be between 175 and 225 PPM, and for concrete or plaster pools, it should be between 200 and 275 PPM.

To raise your calcium hardness by 50 PPM, you’ll need to add about 5 pounds of increaser for every 10,000 gallons. But if you take your pool down at the end of the season, you don’t need to worry about adding this since poor calcium levels do more damage over time. Unfortunately, the only way to lower your calcium is by partially draining and refilling your pool with fresh, filtered water.

7. Shock

Shock is used to refresh your free chlorine levels and keep it actively sanitizing your water. Both non-chlorine and chlorine shock help do this. Chlorine shock, specifically, is more powerful and handy for getting rid of algae or contaminants. Non-chlorine shock can be used once a week or as often as needed by following the instructions on the packaging. But if you need to tackle a big water problem and want to use chlorine shock, you may need a double or triple dose of shock. So be sure to check out our other video for more help on adding the right amount of shock to your pool.

Here Are 3 Ways to Get More Pool Maintenance Help

1. Download our FREE Pool Care Cheat Sheet: It’s a free, easy-to-use guide to help you keep track of taking care of your pool.
2. The Pool Care Course: You’ll get 30+ step-by-step videos and a downloadable guide with everything you need to know about pool maintenance.
3. The Pool Care Handbook: It's an illustrated guide to DIY pool care, including water chemistry, maintenance, troubleshooting, and more.